Zip HydroTap Operations Instructions download pdf (Page 14)

HydroTap Installation and Operating Instructions_Commercial_BCH 4in1_BH 3in1_October 2012_V1.05 Page 14 of 24

1. Position the Font template (provided) on the bench area. Ensure the

position you select is within the length of the supply tube and USB cable

fixed to the Tap Head Assembly. These cannot be extended.

2. Check again for correct positioning. The supply hoses must have

constant fall back to the tank assembly. Cut the holes as shown on the

template.

3. Once holes are cut, locate the Font base in position, from the underside,

lightly tighten the securing rod with the nut and washer provided.

4. Apply a light smear of silicon sealant to the underside of the black base

ring, this will provide a water tight seal against the Font base when

clamped.

* Ensure the plastic spacer is correctly located under the Font.

5. Now take the Tap Head Assembly. Feed the hoses and USB cable

through the Font base, then through the plastic spacer that sits under

the font base but on the bench top. This stops warping of the base

plate. Ensure the Tap spout is directly centred over the Font drain. Fit

the “Spider Clamp”, nut and washer onto the “All Thread”. Have all the

supply tubes and USB cable located evenly between the “Spider Clamp”

legs. When satisfied with the positioning, tighten the fixing nut with the

Tube Spanner provided in the kit.

6. Tighten the securing pin so the Font base is flush with the bench top.

NOTE: The fixing nut above the drain elbow can be loosened to correctly

position the direction of the elbow. Ensure when the re-positioning is

complete the nut is re-tightened to ensure a water tight seal.

7. Connect a drain hose (22mm ID) from the Font base outlet elbow to the

closest drain trap spigot available. If a spigot is not available use the

snap on spigot and worm drive clamps supplied in the kit. (Instructions

and diagrams are supplied in the kit).

8. Ensure the positioning of the snap-on spigot is on the “sink” side of the

trap and not the “waste” side. Once positioned, a hole (13mm ID) will

need to be drilled to provide waste access to the drain line. The snap-on

unit will require suitable sealant to keep it water tight against the waste

pipe. Finish by fitting the worm drive clamps tightly on either side of the

spigot and fitting worm drive clamps to either end of the drain hose.

The drain hose from the Font must have constant fall

9. Connect the Tap head Assembly supply hoses and vent as per the

instructions contained in the installation procedure section of this

document.

NOTE: A stainless steel washer is supplied to go in between the Spider

Clamp and the underside of the benchtop. See location as shown.

Tap assy

hole 35mm

Hole required for Font

recess 108mm

Fixing stud

Drain elbow

View from underside

Cut a 10mm

slot for stud

Black

Plastic

Spacer

See note 4.

Spider

Clamp

Fixing nut

S/S Washer

Tap

All-thread rod

Benchtop

Font

Spacer

Under Font

Operating the Mixer Tap

The Mixer tap is operated as a conventional ‘Flick Mixer’

Lifting the handle up will increase the flow rate and lowering the handle will

reduce the flow rate. Push the handle all the way down to turn the tap off. (For

Standard and Tall tap) For Square tap pulling the handle backwards away from

the tap body increases the flow and pushing forwards towards the tap body

decreases the flow.

When the handle is moved to the left, the temperature is increased and when

moved to the right the temperature is decreased. The final temperature will be

dependant on the temperature of the incoming cold water.

The spout may be swivelled, left or right, for convenience.

Font Installation Procedure

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 23 24

Comments to this Manuals

No comments

Zip HydroTap Operations Instructions Page 14

Comments to this Manuals